Interlocking Garter Springs

Part Number	CAD	D0 (mm)	d (mm)	D1 (mm)	L1 (mm)	L2 (mm)	F1 (N)	D2 (mm)	Qty
G0400080813S		1.02	0.20	65.53	206.50	209.68	0.70	79.83	Add
G0500090170S		1.27	0.23	13.56	43.33	49.00	1.53	16.29	Add
G0500090249S		1.27	0.23	19.94	63.35	72.47	1.32	25.56	Add
G0500100370S		1.27	0.25	29.72	94.16	101.50	1.53	35.97	Add
G0500100695S		1.27	0.25	56.01	176.76	184.73	1.81	65.03	Add
G0500110492S		1.27	0.28	39.55	125.12	133.02	1.88	46.25	Add
G0620080078S		1.57	0.20	6.12	19.86	26.16	0.70	8.26	Add
G0620100168S		1.57	0.25	13.36	42.77	50.27	1.53	17.63	Add
G0620100350S		1.57	0.25	28.04	88.90	93.65	0.91	37.30	Add
G0620100700S		1.57	0.25	56.34	177.80	182.55	0.80	76.06	Add
G0620101400S		1.57	0.25	112.93	355.60	360.35	0.75	152.45	Add
G0620110249S		1.57	0.28	19.91	63.35	74.04	1.33	26.88	Add
G0620110350S		1.57	0.28	28.02	88.90	93.65	1.20	36.70	Add
G0620110366S		1.57	0.28	29.36	93.12	103.96	1.62	38.55	Add
G0620110700S		1.57	0.28	56.31	177.80	182.55	1.01	75.02	Add
G0620111400S		1.57	0.28	112.90	355.60	360.35	0.92	151.60	Add
G0620120350S		1.57	0.30	27.99	88.90	93.65	1.71	34.33	Add
G0620120538S		1.57	0.30	43.26	136.86	146.43	1.95	53.48	Add
G0620120694S		1.57	0.30	55.85	176.43	188.01	2.18	68.04	Add
G0620120700S		1.57	0.30	56.29	177.80	182.55	1.41	70.26	Add

INTERLOCK GARTER SPRINGS

Stock sizes in stainless steel

Garter springs are extension springs with the ends fastened together to form a ring. They are primarily used to maintain controlled pressure of a radial lip seal on a shaft and to compensate for lip wear, changes in volume or stiffness of the elastomer caused by the fluid, and the effect of temperature changes and time. Other uses include small motor belts and electrical connectors.  SPEC garter springs are engineered and manufactured to provide a consistent and reliable product. They feature high initial tension to provide constant load and a special tapered end to assure a strong connection and a continuous near uniform body diameter.

Applications

• Oil Seals • Lip Seals • Small Motor Belts
• Electrical Connectors

Lengths

SPEC garter springs are available in a variety of standard lengths which can be trimmed and assembled to meet your required inside diameter. Simply trim the non-tapered end to your needed length and assemble by screwing the tapered end into the non-tapered end as shown in figure above.

Material

Stainless steel – plain finish.

Type 302 per ASTM A313 or AMS 5688 spring temper.  (Chemical and physical only.) Certificate of chemical analysis available at additional charge.

Tolerances

Body O.D. ±0.13

Load at 4.75mm extension ±10%

Ends

Springs are sold in unassembled lengths with interlock ends.

Back to site top ↑