Clover Dome Spring Washers - Stainless

Info

D_h (mm) min max

D_r (mm) min max

D₀ (mm) min max

Just click and slide the buttons above to specify your search criteria.

Part Number	D_h (mm)	D_r (mm)	D₀ (mm)	D_H (mm)	t (mm)	L₀ (mm)	L₁ (mm)	P₁ (N)	Pf (N)
BC0375010S	4.95	4.95	9.53	9.53	0.25	0.79	0.39	48-73	44
BC0250008S	3.18	3.18	6.35	6.35	0.20	0.56	0.29	27.1-40.5	49
BC0896015S	8.00	8.13	22.76	23.02	0.38	2.06	0.80	76.2-114.3	85
BC0312012S	3.51	3.63	7.92	7.95	0.30	0.81	0.43	81.4-122.4	102
BC0709015S	6.35	6.48	18.01	18.26	0.38	1.70	0.71	79.2-118.8	120
BC0250012S	3.18	3.18	6.35	6.35	0.30	0.66	0.39	78.3-117	151
BC0343014S	4.17	4.29	8.71	8.74	0.36	0.86	0.48	106.3-159.7	156
BC0500014S	6.35	6.48	12.70	12.70	0.36	1.07	0.53	93.9-140.6	160
BC0625018S	7.95	8.05	15.88	15.88	0.46	1.37	0.69	112.5-169	196
BC0375016S	4.95	4.95	9.53	9.53	0.41	0.94	0.54	102-155	200
BC0896020S	8.00	8.13	22.76	23.02	0.51	2.18	0.93	141.9-212.8	209
BC1070020S	9.53	10.16	27.15	28.00	0.51	2.46	1.00	141.8-212.7	209
BC0500018S	6.35	6.48	12.70	12.70	0.46	1.17	0.64	127.7-191.7	222
BC0343016S	4.17	4.29	8.71	8.74	0.41	0.91	0.53	118-179	231
BC0709020S	6.35	6.48	18.01	18.26	0.51	1.83	0.84	151-226.4	249
BC0375018S	4.95	4.95	9.53	9.53	0.46	0.99	0.59	145-220	285
BC0562020S	4.95	4.95	14.27	14.30	0.51	1.57	0.77	181-274	311
BC0437018S	5.59	5.59	11.10	11.13	0.46	1.09	0.62	160.1-240.2	316
BC1070025S	9.53	10.16	27.15	28.00	0.64	2.59	1.12	222.3-334.4	347
BC0750022S	9.53	9.65	19.05	19.05	0.56	1.65	0.83	205.5-308.3	351

CLOVER DOME SPRING WASHERS™

Clover Dome™ spring washers are well suited for applications where a belleville washer or disc spring does not provide adequate deflection, or where the load obtained from a wave washer is not sufficient for application. By combining washers in various sequences, each size provides multiple load-carrying or deflection possibilities. These washers have had the set removed during the manufacturing process.

MATERIAL

Stainless steel: 17-7 PH per AMS5529

Carbon steel: Commercial 1074 - certified to ASTM A684

LOAD & DEFLECTION

(Include drawing from catalogue)

Typical load-deflection curves for three characteristic proportions of washers listed are shown Figure 1 below (include graph from catalogue)

From them, loads at intermediate heights may be estimated. The nominal amount of dish or cone (h) is found by subtracting ‘t’ from ‘H’.

The typical curves show deflections beyond 75%. The area beyond 75% should be avoided due to partial bottoming of the Clover Dome™ and excessive stress concentrations above 75% deflection

Back to site top ↑